How To Set Co2 On Kegerator

Whether you are pouring typhoon beer at home past manner of a kegerator or in a commercial setting using a more complex setup, a beer regulator is a crucial piece of dispensing equipment.

What Are Draft Beer Regulators?

The contents of CO2 & nitrogen gas tanks are under extremely high pressure. The main function of any regulator is to lower that pressure to a safer, more than usable level earlier the gas reaches the keg. The regulator is also responsible for maintaining the optimal carbonation level of the beer beingness dispensed.

Parts of a Typhoon Beer Regulator

• Low pressure gauge: Measures the pressure of the gas going into your keg.
• High pressure gauge: Measures the amount of gas remaining in the tank.
• Shut off valve: Opens and closes the period of gas from the tank to the regulator and keg. Catamenia is open when the lever is parallel to the gas line, and closed when perpendicular to the line.
• Pressure adjustment: Sets the level of force per unit area going to the keg. This may be adjusted past turning a spiral or knob depending on the model of your regulator.
• Outlet plumbing fixtures: Connects air line from keg coupler to the regulator.
• CO2 inlet: Connects regulator to gas tank. Utilise an air tank wrench to tighten or loosen the inlet nut.
• Force per unit area release valve: Pull to release gas from the system

---

Types of Typhoon Beer Regulators

CO2 Regulator

A main CO2 regulator hooks upward to your CO2 tank. In uncomplicated draft configurations, the air line then runs from the regulator to the keg coupler. If you lot are dispensing multiple kegs from 1 tank of gas, the airline might laissez passer through a gas blender or secondary regulator before reaching the coupler.

---

Nitrogen Regulator

If you want to manipulate Guinness or whatsoever other nitro beer, you'll demand a primary Nitrogen regulator. Like a principal CO2 regulator, information technology connects directly to the gas tank or cylinder to moderate its pressure. Unlike a CO2 regulator, information technology attaches to the tank past way of a female stem piece. A CO2 regulator will not properly attach to a Nitrogen tank. If y'all want to manipulate a nitro beer without investing in a Nitrogen regulator, you can purchase a CO2 to nitrogen adapter slice instead.

Whether you are talking Nitrogen or CO2, primary regulators come in unmarried-gauge and double-guess models. Unmarried-guess regulators only have a low-pressure estimate, which measures from 0  to threescore PSI the output pressure of the gas being dispensed into the keg. Double-gauge regulators (shown higher up) accept both a depression-pressure gauge and a high pressure guess, which measures from 0 to 3000 PSI the amount of CO2 or Nitrogen left in the tank. A high-pressure judge is extremely helpful merely not essential to draft beer dispensing.

---

Secondary Regulator

If you are dispensing two or more kegs from a single gas source, a secondary beer regulator may be required. That's because different beers often call for dissimilar dispensing pressures to maintain the carbonation level prescribed past the brewer. Failure to adhere to the brewer's recommendation is to run a risk changing the advent, mouthfeel, and taste of a beer.

---

Distribution Bar

To dispense multiple kegs all at the same pressure, yous'll need a distribution bar, which is basically a large splitter. The primary regulator determines the pressure of gas flowing through a distributor. A distribution bar does not allow yous to adjust the pressure for each keg.

---

Troubleshooting Improper Dispensing Pressure level

Most beers are dispensed somewhere in the range of 10 to 15 PSI. If you are pouring a nitro beer, that range increases to 30 to twoscore PSI. For more information on how to properly set the pressure for your draft beer system consult our guide to Determining the Right Force per unit area for Your Draft Beer System equally well as our 8 Answers to Often Asked Draft Beer CO2 Questions.

A dispensing pressure level that's too low volition result in excessive cream as the gas dissolved in the beer comes out of solution. Eventually, the keg volition dispense flat beer.

To correct the problem, make sure your regulator is set to the proper PSI. If information technology isn't, turn the adjustment screw clockwise to raise the force per unit area to the prescribed level. Otherwise, you lot should make certain that your CO2 tank is on and not empty, and that the the air line is non obstructed. If all of those things check out and y'all are still getting foamy to flat beer, you may need to supervene upon your regulator or gauge. Regulators practise wear down with fourth dimension and utilize. You will by and large need to replace them every four to six years.

A too-high dispensing pressure will force additional gas into the beer, leaving y'all with foamy beer that comes quickly out of the faucet. If your beer is over-carbonated, the foam will appear tight with big bubbles.

If you encounter this trouble, it's easy to ready. Turn the aligning screw counterclockwise to lower the pressure to the proper level and then draw a few foamy pitchers. You tin can too utilize your coupler's relief valve to bleed out the extra pressure. These measures volition force your system to residue itself out again.

If you're having bug with pouring pints from your kegerator or draft beer organisation, and then check out our tips for Troubleshooting Your Draft Beer System.

KegWorks

KegWorks has been selling absurd tools for drinking and serving noesis on tap since 1998. Nosotros are all about enjoying good drinks with practiced friends.

Source: https://content.kegworks.com/blog/pressure-co2-nitrogen-beer-regulators-guide

Share this post